A single spring mechanical seal loads the rotating face with one spring: a cylindrical coil, a conical coil or a diaphragm. The face assembly is a pusher, sliding along the shaft or sleeve as the faces wear, with an O-ring or a PTFE wedge as the secondary seal. One spring means one load path, few places for debris to collect and a short axial stack.

The range covers the shapes this design takes: the W20 diaphragm seal, the WM2N conical spring seal, the W155 and W250 pusher seals, the WUS-2 O-ring seal and the WM3N. References are listed against the seal they replace, so the W20 can be compared with a Vulcan Type 20 and the WM2N with a Burgmann M2N.

What single spring mechanical seals cover

The spring sits behind the rotating face, usually outside the product, and pushes the face onto the seat. Coil versions suit deeper chambers, conical versions compress into a shorter stack, and diaphragm versions combine spring and secondary seal in one moulded part. With only one spring, the face load is applied at the centre. That is an advantage on small shafts and a limitation on large ones, where shaft deflection tilts the face.

Single spring seals tolerate dirty and viscous products better than multi-spring designs because there is no ring of small springs to clog. They are also quicker to strip and rebuild, which matters in workshops that service rather than replace. The limits are pressure and shaft size: past the balance limit of a given design the face load becomes uneven, and a larger shaft needs the load spread around the circumference.

How to specify

  • Shaft diameter and whether the shaft is bare, sleeved or stepped at the seal position.
  • Chamber bore and depth. A conical or diaphragm version buys axial room when the chamber is short.
  • Gland type and bolt pattern, plus whether the existing gland can be reused with a new spring unit.
  • Fluid behaviour. Solids, viscosity and crystallisation are the reasons this family is chosen at all, so describe them.
  • Pressure, temperature and elastomer, with shaft speed if the pump runs above 3,000 rpm.

Typical applications

  • Irrigation and agricultural transfer pumps
  • Machine tool coolant and coolant recovery systems
  • Sump and drain pumps handling dirty water
  • Sugar, syrup and other viscous product transfer
  • Food plant washdown pumps on intermittent duty

What we supply in this range

Ordering and cross-reference

For a single spring seal the critical dimensions are few: shaft diameter, chamber depth and the gap from gland face to seat. Send those with the old seal number or a photograph of the unit beside a rule. If the pump has been rebuilt before, say so; a non-standard seat depth is common after a previous repair. Victor's checks the spring type against the chamber length before quoting, because a coil unit will not fit where a diaphragm was originally used. The family belongs to the wider component mechanical seal range.

FAQ

Why choose one spring instead of several?

Dirty, viscous or crystallising products clog a multi-spring pack. A single spring keeps the load path clear, and it is quicker to rebuild when only the two faces need renewing.

Can a single spring seal run dry?

No seal in this range should run dry for long. A single spring design has less thermal mass in the faces than a cartridge, so dry running damages it quickly.

single spring mechanical seal

A single spring mechanical seal is a type of mechanical seal that uses a single, large coil spring to provide the necessary force to keep the seal faces pressed together. This simple design is a common and cost-effective solution for preventing fluid leakage in various types of rotating equipment, such as pumps and compressors.

Advanced CNC Machining & Premium Materials

Victor use high-precision CNC machines to manufacture metal components with tight tolerances. Only top-grade raw materials are selected for durability and performance.

Custom Mechanical Seal Development

We design tailor-made seals for unique pump requirements, ensuring optimal fit and performance in marine environments.

Fast After-Sales Response

Our team provides quick technical support and troubleshooting to minimize downtime and keep your vessels operational.

how do single coil spring seal work?

Single coil spring seal rely on one coil spring to apply a consistent axial force that keeps the rotating face pressed against the stationary face. As the shaft rotates, a thin film of the process fluid exists between the two faces, which provides lubrication and cools the sealing surfaces, preventing direct metal-to-metal contact.

The single spring also compensates for shaft movement — such as axial shift, thermal expansion, or vibration — by flexing to maintain constant contact, ensuring leak-free performance under changing operating conditions. Depending on design, the spring’s wind direction (right- or left-hand) corresponds to the shaft’s rotation to avoid spring unwinding.

Overall, this simple but robust mechanism offers reliable sealing with fewer components, reducing the risk of clogging and making maintenance easier.

features of single spring seal

unbalanced single spring design

Single spring mechanical seals use a straightforward pusher-type or elastomer-supported structure with an unbalanced design,. This simplicity makes them cost-effective, easy to install, and suitable for a wide range of pump types. The single conical or cylindrical spring provides uniform face loading, ensuring steady and reliable sealing performance even in applications with low solids content or fluctuating operating conditions.

reliable torque transmission

These seals feature dependable torque transmission through a conical spring, bayonet drive, or O-ring compression, ensuring stable operation. Depending on the model, they can be either direction-dependent or direction-independent, providing flexibility for various shaft rotation conditions. Designs that avoid torsion on the bellows or spring further improve reliability and reduce wear.

flexible installation options

Single spring seals support a wide range of rotary face, seat, elastomer, and metal combinations, allowing them to handle water, oils, chemicals, and light abrasive media. Their compact geometry—often with minimal outer diameter and short installation length—makes them easy to fit into tight equipment spaces. With both metric and inch sizes available, they integrate seamlessly into global pump standards and applications.

single coil mechanical seal applications

water and wastewater treatment seal

In water and wastewater applications, single spring seals are widely used in pumps that handle clean water, light chemicals, and treated effluent. These environments typically have moderate pressure and temperature, making them ideal for the straightforward design of single spring seals. The open coil of the spring allows for some self-cleaning, which is beneficial for sealing fluids that might have a small amount of solids.

* Victor recommends using an unbalanced single spring seal with an elastomer bellows, such as the Type 21, in this application for its adaptability to shaft misalignment and general reliability.

For HVAC (Heating, Ventilation, and Air Conditioning) and cooling water systems, single spring seals are a common and effective solution. These systems circulate water and other coolants at moderate temperatures and pressures, conditions that are well within the operating range of a standard single spring seal. Their ease of installation and maintenance is a significant advantage in these applications, as it helps to reduce downtime for routine service.

* Victor suggests a simple, single coil spring seal in these systems, often with a carbon face and ceramic seat, for its robust performance in clean water environments.

General industrial applications, including various centrifugal, rotary, and turbine pumps, frequently utilize single spring seals. These seals are used for a wide range of fluids, from oils and lubricants to non-hazardous chemicals. Their versatility and durability make them a go-to choice for manufacturing, processing, and other general-purpose duties where extreme conditions are not a factor.

* Victor recommends considering a balanced single spring seal for higher pressures, which provides better performance and longer life by distributing face load more evenly.

single spring mechanical seal materials

Material selection plays a decisive role in the durability and stability of single spring seals. By combining hard, soft, and elastomeric materials strategically, Victor’s single spring seals deliver balanced performance, extended service life, and reliable sealing even under fluctuating conditions.

rotary face & stationary seat materials

Carbon: Carbon is widely used in single spring mechanical seals because it offers excellent lubricity, low friction, and good chemical resistance. It runs well against hard faces like SiC and TC, providing stable sealing performance.
Silicon Carbide (SiC / RBSiC / SSIC): Silicon carbide provides superior hardness, excellent thermal conductivity, and strong wear resistance, making it ideal for demanding applications. SSIC offers the highest purity and corrosion resistance among SiC options.
Ceramic: Ceramic is a cost-effective sealing face material with good hardness, chemical stability, and smooth surface finish. It is suitable for general water, light chemicals, and low-to-medium duty applications.
Tungsten Carbide (TC): Tungsten carbide offers exceptional wear resistance and strength, making it ideal for abrasive media or high-pressure conditions. It is also highly durable when paired with carbon.

secondary seal materials

NBR: NBR O-rings provide good resistance to oils and general fluids, making them a common choice for standard pump applications.
EPDM: EPDM performs well in hot water, steam, and many chemicals but is not suitable for oils. It is commonly used in water treatment and HVAC systems.
Viton (FKM): Viton offers excellent high-temperature and chemical resistance, making it ideal for aggressive media and industrial chemicals.
Aflas: Aflas provides outstanding resistance to strong chemicals, amines, and high-temperature environments, often used in oil & gas and chemical processing.

springs & metal components materials

304 Stainless Steel: 304 stainless steel is cost-effective and provides good corrosion resistance for general industrial applications. It is commonly used in standard mechanical seal hardware.
316 Stainless Steel: 316 stainless steel offers enhanced corrosion resistance due to its molybdenum content, making it suitable for seawater, chemicals, and more aggressive fluids.

single spring mechanical seal FAQ

Related blogs

Acquire all kinds of knowledge from professional China pump mechanical seal manufacturer

Why choose a wave spring over multiple springs in mechanical seals?

For most modern mechanical seal designs, wave springs are the preferred axial loading solution over multiple coil springs, as they deliver a more compact profile, more uniform face loading, higher reliability, and lower total installed cost. Spring selection is a critical performance decision — seal face loading directly impacts leakage

Read More »

When should you use a cartridge mechanical seal?

Cartridge mechanical seals are the preferred choice when installation reliability, minimal downtime, and consistent performance in critical applications are top priorities. A cartridge seal is a factory-preassembled, self-contained module: all components — seal faces, springs, sleeve, and gland — are aligned and set at the factory, so the unit arrives

Read More »

Metal Bellow Seals vs Standard Seals: What’s Better?

Metal bellow seals are the clear choice for high-performance, extreme-condition service, while standard pusher seals deliver reliable performance at lower cost for moderate, general-purpose applications. This core tradeoff defines nearly every mechanical seal selection decision. Neither design is universally superior. Each serves a distinct duty range, and matching the seal

Read More »

When does a component seal still make sense?

Component mechanical seals remain the optimal choice in three common scenarios: when equipment was originally engineered for component-style seals and a like-for-like replacement is required; when a compact, integrated design with high reliability and simplified assembly is a priority; and when upgrading to a cartridge seal would add unnecessary complexity

Read More »

How long do pump mechanical seals last?

A pump mechanical seal typically lasts between one and three years, but this can change a lot depending on several factors. Some seals can last for five years or more, while others might fail in just a few days.

The main things that affect a seal’s lifespan are:

The fluid being pumped: Abrasive or corrosive fluids will wear out a seal much faster than clean water.

Operating conditions: High temperatures, high pressure, or the pump running dry will quickly damage a seal.

Correct installation: If a seal is not installed perfectly, it can fail almost immediately.

The right seal for the job: Using a seal that isn’t designed for the specific fluid or conditions will lead to a short life.

The pressure rating for a single coil mechanical seal can vary quite a bit, but it’s generally suited for low to moderate pressure applications, typically up to around 20 bar (about 290 psi).

1. Prepare and Clean
First, make sure the pump is shut down and all power is off. Drain any fluid from the pump. Then, take apart the pump to get to the old seal. Clean the shaft, seal chamber, and all pump parts thoroughly. It’s very important to remove all old seal residue, rust, or dirt.

2. Inspect the Seal and Shaft
Carefully inspect the new seal for any damage. Make sure you don’t touch the seal faces with your bare hands, as oils from your skin can cause problems. Check the pump shaft for any scratches or nicks that could damage the new seal’s O-rings.

3. Install the Stationary and Rotating Parts
Slide the rotating part of the seal onto the pump shaft. You might need to use a clean lubricant to help it slide on smoothly. Then, install the stationary part of the seal into the pump’s seal chamber. Make sure both parts are seated correctly and are perfectly aligned.

4. Set the Seal and Reassemble
Following the manufacturer’s instructions, set the proper compression for the seal spring. This step is critical for the seal to work properly. Finally, reassemble the pump, making sure all bolts are tightened evenly to avoid any misalignment. After assembly, check for any movement of the shaft or seal to ensure everything is secure.

Single coil mechanical seal uses one large, robust coil that resists corrosion and is less prone to clogging in viscous or dirty media. However, compared with multi-spring designs, they provide less uniform face loading and require more axial space. They also depend more on rotation direction, which can limit application flexibility.

Multi-spring mechanical seals use several small springs to deliver even, consistent face pressure, giving them better performance at higher speeds and pressures. They also offer easier standardization across seal sizes. But compared with single spring seals, their thin spring wires are more susceptible to corrosion and clogging in contaminated fluids.