


WM3N O-ring mechanical seals Burgmann M3N replacement
Analog to the following mechanical seals
– Burgmann M3N
– Flowserve Pac-Seal 38
– Vulcan Type 8
– AESSEAL T01
– ROTEN 2
– ANGA A3
– Lidering M211K
Features
For plain shafts
Single seal
Unbalanced
Rotating conical spring
Dependent on direction of rotation
Advantages
Universal application opportunities
Insensitive to low solids content
No damage of the shaft by set screws
Large choice of materials
Short installation lengths possible (G16)
Variants with shrink-fitted seal face available
Recommended applications
Chemical industry
Pulp and paper industry
Water and waste water technology
Building services industry
Food and beverage industry
Sugar industry
Low solids content media
Water and sewage water pumps
Submersible pumps
Chemical standard pumps
Eccentric screw pumps
Cooling water pumps
Basic sterile applications
Operating range
Shaft diameter:
d1 = 6 … 80 mm (0,24″ … 3,15″)
Pressure: p1 = 10 bar (145 PSI)
Temperature:
t = -20 °C … +140 °C (-4 °F … +355 °F)
Sliding velocity: vg = 15 m/s (50 ft/s)
Axial movement: ±1.0 mm
Combination material
Rotary Face
Silicon carbide (RBSIC)
Tungsten carbide
Cr-Ni-Mo Steel (SUS316)
Surface hard facing tungsten carbide
Stationary Seat
Carbon graphite resin impregnated
Silicon carbide (RBSIC)
Tungsten carbide
Auxiliary Seal
Nitrile-Butadiene-Rubber (NBR)
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless Steel (SUS304)
Stainless Steel (SUS316)
Left rotation: L Right rotation:
Metal Parts
Stainless Steel (SUS304)
Stainless Steel (SUS316)
Item Part No. to DIN 24250 Description
1.1 472 Seal face
1.2 412.1 O-Ring
1.3 474 Thrust ring
1.4 478 Righthand spring
1.4 479 Lefthand spring
2 475 Seat (G9)
3 412.2 O-Ring
WM3N dimension data sheet (mm)
Description
WM3N O-ring mechanical seals Burgmann M3N replacement is a replacement seal supplied for general pump duty. Most units go into pulp and paper process water. Bore and shaft tolerances follow the original part, so no adaptor is needed.
Internally the seal uses a conical spring that keeps the seal short in axial length. Standard build pairs carbon graphite with silicon carbide faces and NBR O-rings. The unit is unbalanced, which suits the lower pressure range it is designed for.
Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. Keep the faces clean during fitting; a single grit particle will open a leak path.
Check the shaft for wear at the secondary seal track and the chamber for scoring before the new unit goes on. The first signs of wear are a slow leak at the secondary seal and a light polish on the faces.
As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Fitting a complete replacement keeps the face load and working height as they left the factory, rather than rebuilding the stack on site. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.
Send the nameplate data with the model and shaft size, and the unit is checked against the original drawing. The unit belongs to the mechanical seal line. For a different shaft size, see WE41 O-ring mechanical seals replace Burgmann BT-RN or WH7N O-Ring Component mechanical seals, Eagle burgmann H7N replacement. Include the quantity and the required elastomer option with the enquiry. A seal that has run dry shows heat colouring on the faces before it shows a leak.