Not every pump in a plant comes from a brand with its own seal page. Japanese marine pumps, positive displacement pumps, wastewater pumps and small OEM units all use seals identified by the pump maker plus a shaft size, and the seal is often a cartridge or metal bellows design rather than a simple pusher. This category collects those parts.

Victor supplies seals for Naniwa BBH-50DNC and 34.4 mm pumps, Taiko Kikai HC-51MJ and Taiko 520 pumps, ABS wastewater pumps, Wilo EMU, KRAL ALP, the Waukesha U-1/U-2 200 series and the Inoxpa SLR, Jabsco and Prolac pumps that use the Vulcan 50 pattern.

Seal types used on these pumps

The Japanese marine pumps take cartridge seals: Naniwa BBH-50DNC uses a metal bellows cartridge on a 34.4 mm shaft, and Taiko Kikai HC-51MJ uses a 35 mm cartridge in SiC, carbon, TC and Viton. The Taiko 520 pump takes a multi-spring seal in 20, 30, 40 and 50 mm.

Wastewater and positive displacement pumps take different shapes. ABS pumps use an upper wave spring seal, Wilo EMU uses a cartridge in 35, 50 or 75 mm, KRAL ALP takes a 16, 25 or 35 mm seal, and the Waukesha U-1/U-2 200 series uses single or double seals in the same housing.

How to identify the right replacement

There is no single nameplate rule here. What works is pump maker, shaft size and seal style together, because a cartridge seal with a setting clip cannot be replaced by a component seal without changing the housing. OEM against original seals is the decision most buyers face on these older pumps.

  • Pump maker and model: Naniwa BBH-50DNC, Taiko 520, ABS, Wilo EMU, KRAL ALP, Waukesha U-1/U-2 200, Inoxpa SLR, Jabsco or Prolac.
  • Shaft size: 34.4 mm on the Naniwa cartridge, 35 mm on Taiko, 15.8, 25.4 and 38.1 mm on the Vulcan 50 pattern.
  • Seal style: metal bellows cartridge, wave spring, multi spring or single spring component.
  • Seat: clamped in cartridge designs, gasket mounted on the Vulcan 50 pattern.
  • Face material: SiC, carbon or TC on the marine cartridges; carbon on SiC for clean duties.
  • Elastomer: Viton on marine and hot-oil duty, NBR or EPDM for water.

Materials and duty limits

Marine cartridge seals run SiC, carbon or TC faces with Viton and stainless housings. Wilo EMU cartridges are rated to 2.5 MPa, −30 °C to +200 °C and 15 m/s, with carbon, SiC or TC faces against SiC, TC or carbon.

Waukesha and KRAL seals are built around FKM or EPDM with carbon, ceramic or SiC faces, and the Vulcan 50 pattern adds stainless seats for Jabsco and Inoxpa pumps. Material follows the product: sugar and dairy want EPDM, oils want Viton.

What we supply for these pumps

Cross-reference notes

The one listed equivalence in this category is the Vulcan 50 pattern, which covers Inoxpa SLR, Jabsco and Prolac pumps in 15.8, 25.4 and 38.1 mm. The Naniwa, Taiko, ABS, Wilo, KRAL and Waukesha parts carry no third-party reference in our records, so they are matched on pump model, shaft size and seal style. Where a model has been superseded, measure the shaft and the seat bore before ordering.

FAQ

Can a metal bellows cartridge be replaced with a multi-spring seal?

Only if the housing takes both. A bellows cartridge usually has its own setting length and a clamped seat, and a multi-spring seal of the same shaft size will not match that installed height.

How do I order a seal for a pump with no readable nameplate?

Give the shaft diameter, the seat bore and depth, the seal length and the fluid. Those four measurements identify the housing family even when the pump maker is unknown.