Allweiler builds screw pumps for fuel oil, lube oil and hydraulic service, and their seals are small, O-ring mounted and often ordered by article number rather than shaft size. The SPF10 and SPF20 screw pumps take the WSPF pattern, a 22 mm O-ring mounted seal rated to about 12.6 bar. SOB and SOH pumps, common in ship engine rooms, use the W8X conical spring seal with a gasket mounted seat.

Victor supplies replacements for Allweiler article numbers 33993, 33999, 35362, 38543 and 49680, along with the WSPF and W8X patterns. Article 35362 sits on a 30 mm shaft; the others are identified by the article number printed on the pump drawing rather than by the model.

Seal types used on Allweiler pumps

The WSPF seal is O-ring mounted, self-aligning and non-clogging, built to European non-DIN dimensions, which is why it drops into SPF10 and SPF20 housings without a sleeve change. It suits general and heavy-duty work on fuel and lube oil, about −30 °C to +150 °C.

The W8X is a 22 mm conical spring seal with a gasket mounted seat ring, used on SOB and SOH pumps. Clockwise rotation springs are standard, so pump rotation has to be confirmed before ordering. Article-number seals for 33993, 33999, 35362, 38543 and 49680 follow earlier Allweiler housing patterns where the seat is retained differently.

How to identify the right replacement

The article number on the pump or in the parts list is more reliable than the model code, because the same model was built with different seal housings. Rotation matters too: a conical spring wound for clockwise running will unwind on a counter-clockwise pump and leak within hours. Keeping a replacement seal alive starts with that check.

  • Article number: 33993, 33999, 35362, 38543 or 49680, stamped on the pump or listed in the Allweiler parts book.
  • Pump series: SPF10 and SPF20 for the WSPF pattern; SOB and SOH for the W8X.
  • Shaft diameter: 22 mm on the WSPF and W8X, 30 mm on article 35362.
  • Seat retention: gasket mounted seat on the W8X, O-ring mounted seat on the WSPF; the two do not swap.
  • Elastomer: Viton for hot oil, NBR for cooler service, EPDM where the fluid allows it.

Materials and duty limits

Viton is the default on hot oil and fuel, with NBR on cooler lube oil duty. Faces run SiC against carbon on the WSPF, and ceramic, SiC or carbon on the article-number seals. The WSPF is rated to 12.6 bar and 150 °C; the article-number seals are rated by their housing rather than by one figure.

Where the oil carries abrasive contamination, tungsten carbide faces outlast carbon and cost less than rebuilds. Every Allweiler pattern we list is a replacement matched to the original housing dimensions, so a material upgrade does not change the fit.

What we supply for Allweiler pumps

Cross-reference notes

Cross-reference data here comes from our own listings. The WSPF is listed against Vulcan Type 8W and the W8X against Vulcan type 8X; the shared 22 mm shaft is what makes those references comparable, though the seat retention still differs. The article-number seals for 33993, 33999, 35362, 38543 and 49680 carry no third-party equivalence in our records, so they are matched on article number, shaft size and seat type alone.

FAQ

Can a WSPF seal go into an SOB pump?

No. The WSPF uses an O-ring mounted seat for the SPF housing, while the SOB pump takes the gasket mounted seat of the W8X. The shaft may match and the seal still will not seal.

Why does a new Allweiler seal leak after a bearing change?

The rotor position moved. Shaft end play sets the spring load, so re-check axial position against the drawing before blaming the seal.