Fristam builds sanitary pumps from the FP centrifugal range through FL positive displacement, FSH high-shear and FS blender shafts, and several of their seals are open single-spring designs that sit in the product flow rather than in a closed chamber. The rotating part is driven by a welded-on disc with a groove, the seat is held by pins, and the compression spring is open. That makes the seal easy to clean and sensitive to how it is seated.

Victor supplies seals for the FP, FPX, FL, FT, FKL, FPR, FZX, FM, FPH and FSI lines in 30 mm and 35 mm shaft sizes, including replacements for Vulcan W-2201/1, W3001-1 and W3501-1.

Seal types used on Fristam pumps

The Fristam-2 pattern is the open single-spring seal used across the centrifugal and PD ranges, from FP and FPX pumps to FSH high-shear and powder mixer shafts. It is directional, so the spring has to face the right way, and an O-ring acts as the secondary seal around the shaft.

Fristam-1 and Fristam-3 are clamped-seat versions on 30 mm and 35 mm shafts. Fristam-3 uses a centre seat with lapped faces. Fristam-1 is listed for FP and FPX sizes 633, 735 and 736, and a split two-piece mating ring is available where the seat cannot be drawn out from the front.

How to identify the right replacement

Two Fristam pumps that look alike can take a different seat, because some FPX builds use the split two-piece mating ring so the seat can be changed without pulling the pump apart. Check the pump size code and whether the mating ring is one piece or two. How a single spring seal works covers the drive detail that decides the direction of fit.

  • Pump model and size: FP, FPX, FL, FT, FKL, FPR, FZX, FM, FPH, FSI or FS, with the size code such as 633, 735 or 736.
  • Shaft diameter: 30 mm on most FP and FPX builds, 35 mm on the larger ones.
  • Mating ring: one piece or split two-piece; the split version allows a seat change without stripping the pump.
  • Seat type: centre seat with lapped faces on the Fristam-3 pattern.
  • Rotation: open single-spring seals are directional; check the arrow on the pump before fitting.
  • Elastomer: EPDM for product contact, Viton where fats and oils are present.

Materials and duty limits

Faces run carbon, SiC, SSiC or TC against ceramic, SiC, SSiC or TC seats, with NBR, EPDM or Viton rings and 304 or 316 metal parts. Product contact normally means EPDM with carbon on SiC; high-shear and blender shafts are safer with SiC on SiC.

The Fristam-1 and Fristam-3 patterns come in 304 stainless with Viton, which covers most cleaning-in-place and hot-product duty. Component against cartridge seals is the relevant comparison here, since every pattern on this page is a component seal that relies on the pump housing for alignment.

What we supply for Fristam pumps

Cross-reference notes

Our own listings pair Fristam-1 with Vulcan W-2201/1 and Fristam-3 with Vulcan W3001-1 and W3501-1, on 30 mm and 35 mm shafts. Fristam-2 carries no third-party reference in our records because it is an open single-spring pattern matched to the Fristam housing itself, so the pump model and shaft size are the only safe way to order it.

FAQ

Why does an open Fristam seal leak after a rebuild?

Usually the spring is fitted the wrong way round. The pattern is directional, and a reversed spring loads the faces unevenly and leaks within a shift.

Can a split mating ring be fitted to any FPX pump?

Only where the housing was machined for it. The split ring is a service option on specific builds, not a universal swap.