A cartridge mechanical seal leaves the bench as one pre-set assembly: rotating face, stationary seat, sleeve, gland plate, springs and secondary seals are set at working height and held by clips. Nothing is measured on the pump. The cartridge slides onto the shaft, bolts to the chamber face, the clips come off, and the seal sits at the axial position it was set to during assembly.

This category holds the cartridge units we build: a single balanced seal, an AES CONII pattern and an AES CURC pattern, each with sleeve and gland included. The range is short on purpose. A cartridge is chosen when the chamber has the axial room and when maintenance time, rather than the purchase itself, is the binding constraint.

What cartridge mechanical seals cover

The assembly carries its own flush and quench ports, a throttle or pumping ring where the design calls for one, and a gland that centres the unit on the chamber face. Single versions suit clean, non-hazardous products. Double versions need a barrier fluid and are used where the product must not reach atmosphere. Balanced faces allow more pressure inside the same envelope.

Because working height is fixed at assembly, the seal cannot be installed too deep or too shallow, which is the most common error on component seals. The trade-off is dimensional. A cartridge needs more axial room and a chamber face that is square to the shaft. A corroded or out-of-square face will leak at the gland gasket however well the seal itself was built.

How to specify

  • Shaft or sleeve diameter at the seal, measured on the shaft the cartridge will run on.
  • Chamber bore, depth and face to first obstruction. The last number decides whether the cartridge body clears the impeller nut.
  • Gland bolt circle, thread and orientation, including whether the existing studs can be reused.
  • Ports. Flush, quench and drain positions and threads, since a cartridge with the wrong port layout will not connect.
  • Pressure, temperature and arrangement. Single or double, and the barrier fluid if double.

Typical applications

  • Chemical process pumps on clean and hazardous products
  • Pulp and paper stock pumps after the screen room
  • Boiler feedwater and condensate service
  • Produced water and injection pumps
  • District heating main circulation

What we supply in this range

Ordering and cross-reference

Four dimensions carry a cartridge enquiry: shaft diameter, chamber bore, chamber depth and gland bolt circle. Add the pump model and the old seal code where they exist. A photograph of the chamber face with a rule across it saves a round of questions. If the old unit is a Cartex, CONII or CURC pattern, name it: the bolt circle and port layout usually settle the match. As a mechanical seal supplier we also check whether a component seal would fit the same chamber, since that option is often the simpler fit on a small pump.

FAQ

Do I have to set the working height on site?

No. The clips hold the assembly at the height set during build. Remove them only after the gland bolts are tight, and keep them for the next rebuild.

Can a cartridge replace a component seal?

Only if the chamber has the axial depth and a square face for the gland. Where space is tight, the component version of the same duty is the realistic choice. Our note on what is a cartridge mechanical seal explains the arrangement difference.

cartridge mechanical seal

Cartridge mechanical seals are pre-assembled, factory-set sealing units that integrate the sleeve, gland, seal faces, springs, and all necessary elastomers into a single module. With preset alignment maintained by setting clips, they allow fast, error-free installation and eliminate the fine adjustments required by component seals.

customized cartridge seal engineering

Victor develops cartridge mechanical seals tailored to specific pump designs and operating conditions, ensuring precise fit, stable alignment, and reliable sealing even in demanding applications. We also provide engineered-equivalent cartridge seals for many OEM brands—including IMO, Grundfos, Alfa Laval, Flygt, ABS, Lowara, Allweiler, KRAL, Emu, APV, Fristam, and others.

extensive stock for rapid supply

With a large stock of standard cartridge seal models, Victor minimizes downtime by enabling fast delivery and immediate replacement—ideal for facilities that prioritize quick maintenance and reduced operational interruption.

strict quality validation

Each cartridge seal is fully inspected and pressure-tested as a complete unit before shipping. Dimensional verification, face alignment checks, and leakage testing ensure consistent performance and long service life in the field.

Victor's cartridge mechanical seal

Victor provides high-performance cartridge mechanical seals, engineered for demanding industrial applications and consistent sealing reliability. Each model below is designed with robust construction, easy installation.

how does a cartridge mechanical seal work?

A cartridge mechanical seal works by creating a precision, dynamic interface between a rotating shaft-mounted face and a stationary housing face. These two ultra-flat faces are factory-pre-assembled in a cartridge unit — one face rotates with the pump shaft, while the other remains fixed to the pump housing.

During operation, a thin fluid film forms between the seal faces. This film — from the pumped fluid or a flush/buffer liquid — lubricates and cools the faces while maintaining an effective seal barrier. Concurrently, internal springs or bellows inside the cartridge apply a pre-set closing force to keep the faces in contact under varying pressures.

Because the cartridge is factory aligned and spring tension preset, the risk of installation error is minimized. The seal simply slides onto the shaft, is secured, and the setting clips are removed — making installation quicker and reducing chances of leakage due to misalignment or incorrect compression.

cartridge mechanical seal applications

Victor cartridge mechanical seals are engineered for versatility—one pre-set, self-contained design that adapts to a wide range of pumping conditions across multiple industries. Whether dealing with clean water, corrosive chemicals, lubricating oils, or sanitary-grade process fluids, these seals ensure stable, reliable performance with minimal installation error.

oil mechanical seal

Cartridge seals perform exceptionally well in oil-handling pumps where high pressure, temperature fluctuations, and lubricating media require stable face loading. Their integrated gland and sleeve design minimizes installation errors and ensures consistent sealing performance in lube oil, fuel oil, and hydraulic oil systems.

For clean or slightly contaminated water systems, cartridge seals provide dependable leakage control and long service life. The pre-set spring compression prevents over-tightening during installation, making them ideal for municipal water pumps, HVAC circulation pumps, and industrial water transfer systems.

In pharmaceutical processes that demand hygienic and contamination-free operation, cartridge seals offer controlled face alignment and smooth, stable sealing performance. Their compact, enclosed design reduces the risk of product contamination and supports CIP/SIP cleaning requirements.

Cartridge seals built with corrosion-resistant materials (such as SiC, Hastelloy, or PTFE components) are ideal for pumps handling aggressive chemicals. The isolated, self-contained seal chamber helps protect metal parts from direct chemical attack, ensuring reliable sealing in acid, alkali, and solvent processes.

difference between single and double cartridge mechanical seals

Understanding the difference between single and double cartridge mechanical seals is essential for selecting the right sealing solution for your pump system, especially when balancing reliability, leakage control, and operating conditions.

single cartridge seal

A single cartridge seal uses one pair of seal faces to control leakage, making it a straightforward and economical choice for clean, non-hazardous, and well-lubricating fluids. Because all sealing action depends on one interface, reliability is closely tied to the quality of the process fluid film—any dryness, solids, or vapor pressure instability increases wear and leakage risk. In short, single cartridge mechanical seal is ideal when the pumped medium poses low environmental risk and operating conditions are stable.

double cartridge seal

A dual cartridge seal incorporates two sets of seal faces with a buffer or barrier fluid circulating between them. This secondary sealing interface provides an extra layer of protection, allowing the seal to handle toxic, abrasive, or volatile media that cannot be safely released. The pressurized barrier system also ensures consistent lubrication and cooling regardless of the process fluid quality. Thus, double cartridge seals offer higher reliability and containment in demanding services, especially where safety, emissions control, or uptime is critical.

cartridge mechanical seal materials

Material selection plays a decisive role in the durability and stability of single spring seals. By combining hard, soft, and elastomeric materials strategically, Victor’s single spring seals deliver balanced performance, extended service life, and reliable sealing even under fluctuating conditions.

seal face (stationary/rotary ring) materials

Carbon: Carbon offers excellent lubricity and low friction, helping cartridge mechanical seals run cooler and more stable. It is a cost-effective choice for clean water, light chemicals, and general industrial pumps.
Silicon Carbide (SiC): SiC provides very high hardness and strong wear resistance, making it ideal for cartridge seals used with abrasive fluids or high-pressure conditions. It also performs well in chemical and wastewater applications.
Tungsten Carbide (TC): TC delivers exceptional strength and durability, suitable for heavy-duty cartridge seal applications. It handles high mechanical loads and is reliable in oil & gas, slurry handling, and harsh industrial processes.

secondary seal materials

Viton (FKM): Viton resists heat, oils, fuels, and many chemicals, making it a versatile secondary seal material for cartridge seals in petrochemical and industrial processing pumps.
EPDM: EPDM is highly resistant to water, steam, and polar fluids, making it suitable for cartridge seals in hot water systems, HVAC pumps, and certain food or pharmaceutical applications.
AFLAS: AFLAS withstands high temperatures and aggressive chemicals such as amines and strong bases. It is ideal for cartridge seals operating in chemical plants, power systems, and harsh fluids.
PTFE: PTFE offers outstanding chemical inertness and is used in cartridge seals for acids, solvents, and highly corrosive media. It provides long life but requires precise design due to its low elasticity.

springs & metal component materials

304 Stainless Steel: 304 stainless steel provides good corrosion resistance and strength, making it a dependable option for general-purpose cartridge mechanical seals in water and light chemical applications.
316 Stainless Steel: 316 stainless steel offers enhanced corrosion resistance, especially to chlorides and harsh chemicals. It is preferred for cartridge seals used in marine, chemical, and corrosive service environments.

cartridge mechanical seals FAQ

Related blogs

Acquire all kinds of knowledge from professional China pump seal manufacturer

Why choose a wave spring over multiple springs in mechanical seals?

For most modern mechanical seal designs, wave springs are the preferred axial loading solution over multiple coil springs, as they deliver a more compact profile, more uniform face loading, higher reliability, and lower total installed cost. Spring selection is a critical performance decision — seal face loading directly impacts leakage

Read More »

When should you use a cartridge mechanical seal?

Cartridge mechanical seals are the preferred choice when installation reliability, minimal downtime, and consistent performance in critical applications are top priorities. A cartridge seal is a factory-preassembled, self-contained module: all components — seal faces, springs, sleeve, and gland — are aligned and set at the factory, so the unit arrives

Read More »

Metal Bellow Seals vs Standard Seals: What’s Better?

Metal bellow seals are the clear choice for high-performance, extreme-condition service, while standard pusher seals deliver reliable performance at lower cost for moderate, general-purpose applications. This core tradeoff defines nearly every mechanical seal selection decision. Neither design is universally superior. Each serves a distinct duty range, and matching the seal

Read More »

When does a component seal still make sense?

Component mechanical seals remain the optimal choice in three common scenarios: when equipment was originally engineered for component-style seals and a like-for-like replacement is required; when a compact, integrated design with high reliability and simplified assembly is a priority; and when upgrading to a cartridge seal would add unnecessary complexity

Read More »

What is the difference between cartridge and non cartridge mechanical seals?

A cartridge mechanical seal is a preassembled, self-contained unit that includes the gland, sleeve, and all sealing components with factory-set clearances. This design makes installation fast, accurate, and less dependent on technician skill—reducing measurement errors, misalignment, and startup failures. Cartridge seals also protect the shaft and offer higher reliability, though they cost more and require slightly more space.

A non-cartridge (component) mechanical seal comes as individual parts that must be installed and set manually on the pump shaft. While it is more affordable and flexible for small pumps, it requires skilled installation and precise measurements. Incorrect assembly can shorten seal life or cause immediate failure, and exposed components are more prone to handling damage.

Victor provides both high-quality cartridge mechanical seal and component mechanical seal.

Installing a cartridge mechanical seal is generally more straightforward than installing a component seal because the seal is pre-set at the factory. However, correct procedure is still essential for reliable operation. You can always consult Victor’s technical specialists for professional installation guidance. Here is the simplified process:

  1. Prepare the pump and shaft
    Ensure the pump is isolated, depressurized, and clean. Inspect the shaft or sleeve for wear, burrs, or corrosion, and verify that all surfaces are smooth and within tolerance.
  2. Position the gland gasket and place the seal on the shaft
    Slide the cartridge seal assembly carefully onto the shaft without forcing it. Make sure the gland gasket is correctly seated and not pinched or damaged.
  3. Align the gland and tighten the bolts evenly
    Position the gland over the pump’s bolt circle and tighten bolts in a crisscross pattern. This maintains even loading and prevents distortion of the seal or misalignment against the pump housing.
  4. Set the seal using the shipping clips or setting screws
    Cartridge seals arrive with pre-set axial positioning. Keep the clips or set screws in place until the gland is fully mounted. Once the seal is secured, remove the clips to activate the seal.
  5. Reconnect the system and perform a controlled startup
    Verify lubrication, flush lines, and alignment. Start the pump slowly and check for leakage, noise, or abnormal vibration.

Double cartridge mechanical seals are available in several main configurations, each suited to different application needs. The most common types are:

  • Back-to-Back (also called “side-by-side”) — two seal faces oriented back-to-back, creating a barrier chamber in between. This layout is often used for hazardous or aggressive fluids because the barrier fluid between seals isolates the process from the environment.
  • Face-to-Face — the seal faces are mounted facing each other so the cartridge remains more compact. This type is widely used for compact pumps or installations with limited space; it also facilitates barrier-fluid lubrication and simple maintenance.
  • Tandem (in-series) — two seals arranged sequentially, both oriented in the same direction, used especially where the outer seal acts as backup to the inner seal, often in chemical or high-risk media service. This configuration provides an extra safety margin if the primary seal fails.

Each configuration balances trade-offs between sealing reliability, installation space, barrier fluid handling, and suitability for specific media (corrosive, hazardous, slurry, etc.).