Single balanced cartridge mechanical seals burgmann Cartex S

Features

Single seal
Cartridge
Balanced
Independent of direction of rotation
Single seals without connections (-SNO), with flush (-SN) and with quench combined with lip seal (-QN) or throttle ring (-TN)
Additional variants available for ANSI pumps (e.g. -ABPN) and eccentric screw pumps (-Vario)

Advantages

Ideal seal for standardizations
Universal applicable for packings conversions, retrofits or original equipment
No dimensional modification of the seal chamber (centrifugal pumps) necessary, small radial installation height
No damage of the shaft by dynamically loaded O-Ring
Extended service life
Straightforward and easy installation due to pre-assembled unit
Individual adaptation to pump design possible
Customer specific versions available

Recommended applications

Process industry
Petrochemical industry
Chemical industry
Pharmaceutical industry
Power plant technology
Pulp and paper industry
Water and waste water technology
Mining industry
Food and beverage industry
Sugar industry
CCUS
Lithium
Hydrogen
Sustainable plastics production
Alternative fuels production
Power generation
Universally applicable
Centrifugal pumps
Eccentric screw pumps
Process pumps

Operating range

Cartex-SN, -SNO, -QN, -TN, -Vario

Shaft diameter:
d1 = 25 … 100 mm (1.000″ … 4.000″)
Other sizes on request
Temperature:
t = -40 °C … 220 °C (-40 °F … 428 °F)
(Check O-Ring resistance)

Sliding face material combination BQ1
Pressure: p1 = 25 bar (363 PSI)
Sliding velocity: vg = 16 m/s (52 ft/s)

Sliding face material combination
Q1Q1 or U2Q1
Pressure: p1 = 12 bar (174 PSI)
Sliding velocity: vg = 10 m/s (33 ft/s)

Axial movement:
±1.0 mm, d1 ≥75 mm ±1.5 mm

Combination material

Seal face: Silicon carbide (Q1), Carbon graphite resin impregnated (B), Tungsten carbide (U2)
Seat: Silicon carbide (Q1)
Secondary seals: FKM (V), EPDM (E), FFKM (K), Perflourocarbon rubber/PTFE (U1)
Springs: Hastelloy® C-4 (M)
Metal parts: CrNiMo steel (G), CrNiMo cast steel (G)

cartex s
cartex s 2

Data Sheet of Dimension (mm)

cartex s dimensions
cartex s dimensions 2

Description

Single balanced cartridge mechanical seals burgmann Cartex S is a replacement seal supplied for general pump duty. Typical duty is light-duty chemical transfer. Bore and shaft tolerances follow the original part, so no adaptor is needed.

Sealing geometry follows the original, built around a cartridge build that is set on the bench and fitted as one unit. Standard build pairs carbon graphite with silicon carbide faces and NBR O-rings.

Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. A short dry run is enough to score the faces, so prime the chamber before start-up.

Fitting follows the standard procedure: measure shaft diameter, chamber depth and working height, then set the seal to the recorded dimension before the pump is reassembled. A seal that has run dry shows heat colouring on the faces before it shows a leak.

As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Fitting a complete replacement keeps the face load and working height as they left the factory, rather than rebuilding the stack on site. Keeping one unit on the shelf cuts the downtime that follows a leak, since the pump does not have to wait for a part to arrive.

Orders are matched on pump model, shaft size and medium. The unit belongs to the mechanical seal line. Two close alternatives are WCONII High quality Cartridge Mechanical Seal Replace AES CONII and WCURC Cartridge mechanical seal replace AES CURC. Include the quantity and the required elastomer option with the enquiry. Cross-reference is by pump model and part number, with the shaft and casing dimensions confirmed before the order is released.