


WMG1 Elastomer Bellow Mechanical Seal Replaced Burgmann MG1
Replacement for below mechanical seals
AESSEAL B02, BURGMANN MG1, FLOWSERVE 190
Features
For plain shafts
Single and dual seal
Elastomer bellows rotating
Balanced
Independent of direction of rotation
No torsion on bellows
Advantages
Shaft protection over entire seal length
Protection of seal face during installation due to special bellows design
Insensitive to shaft deflections due to large axial movement ability
Universal application opportunities
Important material certifications available
High flexibility due to wide offer on materials
Suitable for low-end sterile applications
Special design for hot water pumps (RMG12) available
Dimension adaptions and additional seats available
Recommended Applications
Fresh water supply
Building services engineering
Waste water technology
Food technology
Sugar production
Pulp and paper industry
Oil industry
Petrochemical industry
Chemical industry
Water, waste water, slurries (solids up to 5 % by weight)
Pulp (up to 4 % otro)
Latex
Dairies, beverages
Sulfide slurries
Chemicals
Oils
Chemical standard pumps
Helical screw pumps
Stock pumps
Circulating pumps
Submersible pumps
Water and waste water pumps
Oil applications
Operating range
Shaft diameter:
d1 = 10 … 100 mm (0.39″ … 3.94″)
Pressure: p1 = 16 bar (230 PSI),
vacuum … 0.5 bar (7.25 PSI),
up to 1 bar (14.5 PSI) with seat locking
Temperature: t = -20 °C … +140 °C
(-4 °F … +284 °F)
Sliding velocity: vg = 10 m/s (33 ft/s)
Admissible axial movement: ±2.0 mm (±0,08″)
Combination material
Rotary Face
Carbon graphite resin impregnated
Hot-Pressing carbon
Silicon carbide (RBSIC)
Stationary Seat
Aluminium oxide (Ceramic)
Silicon carbide (RBSIC)
Tungsten carbide
Auxiliary Seal
Nitrile-Butadiene-Rubber (NBR)
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless Steel (SUS304)
Metal Parts
Stainless Steel (SUS304)
Notes
The WMG1 can also be used as a multiple seal in tandem or in a back-to-back arrangement. Installation proposals available upon request.
Dimension adaptations for specific conditions, e. g. shaft in inches or special seat dimensions are available upon request.
Item Part No. to DIN 24250 Description
1.1 472 Seal face
1.2 481 Bellows
1.3 484.2 L-ring (spring collar)
1.4 484.1 L-ring (spring collar)
1.5 477 Spring
2 475 Seat
3 412 O-Ring or cup rubber
WMG1 Dimension Date Sheet (mm)
Description
WMG1 Elastomer Bellow Mechanical Seal Replaced Burgmann MG1 is a replacement mechanical seal built to a standard mounting envelope. Typical duty is food and beverage process lines. Bore and shaft tolerances follow the original part, so no adaptor is needed.
The load path runs through an elastomer bellows that seals on the shaft without a separate gasket. Faces are carbon graphite against silicon carbide, with NBR secondary sealing as standard.
Temperature, pressure and speed limits depend on the face and elastomer combination, so the duty point should be checked against the datasheet before the order is released. Keep the faces clean during fitting; a single grit particle will open a leak path.
Check the shaft for wear at the secondary seal track and the chamber for scoring before the new unit goes on. The first signs of wear are a slow leak at the secondary seal and a light polish on the faces.
As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Fitting a complete replacement keeps the face load and working height as they left the factory, rather than rebuilding the stack on site. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.
Pricing and availability follow the pump model and shaft size given on the enquiry. The unit belongs to the Victor’s pump mechanical seal line. For a different shaft size, see AES P02 Elastomer Bellow Mechanical Seal John Crane Type 2 N SEAT or W2100 Elastomer Bellow Mechanical Seal Replacement of John Crane 2100. Include the quantity and the required elastomer option with the enquiry. Cross-reference is by pump model and part number, with the shaft and casing dimensions confirmed before the order is released.