


WMFL85N Metal Bellow Mechanical Seals Replace Eagle Burgmann MFL85N
Features
For unstepped shafts
Single seal
Balanced
Independent of direction of rotation
Metal bellows rotating
Analogue for
Burgmann MFL85N, Chesterton 886, John Crane 680, Latty B17, LIDERING LMB85
Advantages
For extreme temperature ranges
No dynamically loaded O-Ring
Self-cleaning effect
Short installation length possible
Pumping screw for highly viscous media available (dependent on direction of rotation)
Recommended applications
Process industry
Oil and gas industry
Refining technology
Petrochemical industry
Chemical industry
Hot media
Cold media
Highly viscous media
Pumps
Special rotating equipment
Oil
Light hydrocarbon
Aromatic Hydrocarbon
Organic solvents
Week acids
Ammonia
Operating range
Shaft diameter:
d1 = 16 … 100 mm (0.63″ … 4“)
Externally pressurized:
p1 = … 25 bar (363 PSI)
Internally pressurized:
p1 <120 °C (248 °F) 10 bar (145 PSI)
p1 <220 °C (428 °F) 5 bar (72 PSI)
Temperature: t = -40 °C … +220 °C
(-40 °F … 428) °F,
Stationary seat lock necessary.
Sliding velocity: vg = 20 m/s (66 ft/s)
Notes: The range of preesure,temperature and sliding velocity is depend on seals
Combination material
Rotary Face
Silicon carbide (RBSIC)
Carbon graphite resin impregnated
Tungsten carbide
Stationary Seat
Silicon carbide (RBSIC)
Tungsten carbide
Elastomer
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
PTFE Enwrap Viton
Bellows
Alloy C-276
Stainless Steel (SUS316)
AM350 Stainless Steel
Alloy 20
Parts
Stainless Steel (SUS304)
Stainless Steel (SUS316)
Mediums: Hot water, oil, liquid hydrocarbon, acid, alkali, solvents, paper pulp and other medium-and-low-viscosity content.
Item Part No. DIN 24250 Description
1.1 472/481 Seal face with bellows unit
1.2 412.1 O-Ring
1.3 904 Set screw
2 475 Seat (G9)
3 412.2 O-Ring
WMFL85N Dimension Data Sheet (mm)
Description
WMFL85N Metal Bellow Mechanical Seals Replace Eagle Burgmann MFL85N is a replacement seal supplied for general pump duty. It is normally specified for clean water and light chemical service. Bore and shaft tolerances follow the original part, so no adaptor is needed.
The load path runs through a welded metal bellows that takes the elastomer out of the load path. Faces are carbon graphite against silicon carbide, with NBR secondary sealing as standard. The unit is unbalanced, which suits the lower pressure range it is designed for.
Temperature, pressure and speed limits depend on the face and elastomer combination, so the duty point should be checked against the datasheet before the order is released. A short dry run is enough to score the faces, so prime the chamber before start-up.
Check the shaft for wear at the secondary seal track and the chamber for scoring before the new unit goes on. Wear normally appears first at the faces, then at the secondary seals; a leaking unit usually shows both by the time it is pulled.
As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.
Send the nameplate data with the model and shaft size, and the unit is checked against the original drawing. The unit belongs to the Victor’s pump mechanical seal line. For a different shaft size, see WMFWT80 Metal Bellow mechanical seals replace Burgmann MFLWT80 or Metal bellow balanced pump mechanical seals WMF95N. Include the quantity and the required elastomer option with the enquiry.
The reference carried by this unit is WMFL85N. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.