WM7N Water Pump Shaft Seal Replacement Of Eagle Burgmann M7N

Replacement for the below mechanical seals

Burgmann M7N ,LIDERING LWS10, Latty U68, Flowserve Europac 600, Vulcan 1677, AESSEAL W07DMU, Anga V, Sterling 270, Hermetica M251.K2

Features

For plain shafts
Single seal
Unbalanced
Super-Sinus-spring or multiple springs rotating
Independent of direction of rotation

Advantages

Universal application opportunities
Efficient stock keeping due to easily interchangeable faces
Extended selection of materials
Insensitive to low solids contents
Flexibility in torque transmissions
Self-cleaning effect
Short installation length possible (G16)
Pumping screw for media with higher viscosity

Recommended Applications

Process industry
Chemical industry
Pulp and paper industry
Water and waste water technology
Shipbuilding
Lube oils
Low solids content media
Water / sewage water pumps
Chemical standard pumps
Vertical screw pumps
Gear wheel feed pumps
Multistage pumps (drive side)
Circulation of printing colors with viscosity 500 … 15,000 mm2/s.

Operating range

Shaft diameter:
d1 = 14 … 100 mm (0.55 ” … 3.94 “)
Pressure:
p1 = 25 bar (363 PSI)
Temperature:
t = -50 °C … +220 °C
(-58 °F … +428 °F)
Sliding velocity:
vg = 20 m/s (66 ft/s)

Axial movement:
d1 = up to 25 mm: ±1.0 mm
d1 = 28 up to 63 mm: ±1.5 mm
d1 = from 65 mm: ±2.0 mm

Combination material

Rotary Face
Silicon carbide (RBSIC)
Carbon graphite resin impregnated
Tungsten carbide
Cr-Ni-Mo Steel (SUS316)
Stationary Seat
Silicon carbide (RBSIC)
Carbon graphite resin impregnated
Tungsten carbide
Auxiliary Seal
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Silicone-Rubber(MVQ)
PTFE Coated VITON
Spring
Stainless Steel (SUS304)
Stainless Steel (SUS316)
Metal Parts
Stainless Steel (SUS304)
Stainless Steel (SUS316)

wm7n

Item Part no. to DIN 24250 Description

1.1 472 Seal face
1.2 412.1 O-Ring
1.3 474 Thrust ring
1.4 478 Righthand spring
1.4 479 Lefthand spring
2 475 Seat (G9)
3 412.2 O-Ring

WM7N DATA SHEET OF DIMENSION (mm)

WM7N DATA SHEET OF DIMENSION

Description

WM7N Water Pump Shaft Seal Replacement Of Eagle Burgmann M7N is a replacement mechanical seal built to a standard mounting envelope. It is normally specified for cooling water and service water circuits. Bore and shaft tolerances follow the original part, so no adaptor is needed.

The working element is a spring-loaded pusher assembly. The face pair is carbon graphite running on silicon carbide; secondary seals are NBR. The unit is unbalanced, which suits the lower pressure range it is designed for.

Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. Keep the faces clean during fitting; a single grit particle will open a leak path.

Measure shaft diameter, chamber depth and working height before stripping the old unit; the new seal is set to those numbers, not to the dimensions of the worn part. Wear normally appears first at the faces, then at the secondary seals; a leaking unit usually shows both by the time it is pulled.

As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.

Replacement orders are confirmed against the original part number and the shaft size. The unit belongs to the mechanical seal line. Two close alternatives are WH7N O-Ring Component mechanical seals, Eagle burgmann H7N replacement and WMG912 replacement of Burgmann MG912, Single Seal unbalanced mechanical shaft sea. Include the quantity and the required elastomer option with the enquiry.