WHJ92N Wave Spring Mechanical Seals Replacement For Burgmann HJ92N

Features

For unstepped shafts
Single seal
Balanced
Independent of direction of rotation
Encapsulated rotating spring

Advantages

Especially designed for solids containing and highly viscous media
Springs are protected from the product
Rugged and reliable design
No damage of the shaft by dynamically loaded O-Ring
Universal application
Variant for operation under vacuum available
Variants for sterile operation available

Recommended Applications

Pharmaceutical industry
Power plant technology
Pulp and paper industry
Water and waste water technology
Mining industry
Food and beverage industry
Sugar industry
Dirty, abrasive and solids containing media
Thick juice (70 … 75 % sugar content)
Raw sludge, sewage slurries
Raw sludge pumps
Thick juice pumps
Conveying and bottling of dairy products

Operating range

Shaft diameter:
d1 = 18 … 100 mm (0.625″ … 4″)
Pressure:
p1*) = 0.8 abs…. 25 bar (12 abs. … 363 PSI)
Temperature:
t = -50 °C … +220 °C (-58 °F … +430 °F)
Sliding velocity: vg = 20 m/s (66 ft/s)
Axial movement: ±0.5 mm

* An integral stationary seat lock is not needed within the permissible low pressure range. For prolonged operation under vacuum it is necessary to arrange for quenching on the atmospheric side.

Combination material

Rotary Face
Silicon carbide (RBSIC)
Carbon graphite resin impregnated
Antimony Impregnated Carbon
Stationary Seat
Silicon carbide (RBSIC)
Tungsten carbide
Auxiliary Seal
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless Steel (SUS304)
Stainless Steel (SUS316)
Metal Parts
Stainless Steel (SUS304)
Stainless Steel (SUS316)

whj92n

Description

1.1 472/473 Seal face
1.2 485 Drive collar
1.3 412.2 O-Ring
1.4 412.1 O-Ring
1.5 477 Spring
1.6 904 Set screw
2 475 Seat (G16)
3 412.3 O-Ring

WHJ92N data sheet of dimension (mm)

WHJ92N data sheet of dimension

Description

WHJ92N Wave Spring Mechanical Seals Replacement For Burgmann HJ92N is a replacement seal supplied for general pump duty. It is normally specified for building services and HVAC plant. Bore and shaft tolerances follow the original part, so no adaptor is needed.

The design is built around a wave spring that keeps the axial stack short while holding uniform face pressure. The face pair is carbon graphite running on silicon carbide; secondary seals are NBR. It is a balanced design, so face loading stays controlled as pressure rises.

Temperature, pressure and speed limits depend on the face and elastomer combination, so the duty point should be checked against the datasheet before the order is released. Keep the faces clean during fitting; a single grit particle will open a leak path.

Clean the chamber and the shaft before fitting; grit left in the bore will tilt the gland. Wear normally appears first at the faces, then at the secondary seals; a leaking unit usually shows both by the time it is pulled.

EPDM covers water and dilute chemical service but not mineral oils; FKM handles oils, fuels and many solvents; FFKM is reserved for aggressive media where the softer elastomers swell. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.

Send the nameplate data with the model and shaft size, and the unit is checked against the original drawing. The unit belongs to the Victor’s mechanical seal range line. Related units in the same family include WM74D Double face mechanical seals replacement of Burgmann M74D and WH7N O-Ring Component mechanical seals, Eagle burgmann H7N replacement. Include the quantity and the required elastomer option with the enquiry.

The reference carried by this unit is WHJ92N. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.