W58U General Purpose DIN Multi-spring O-ring Pusher Seal

Features

• Mutil-Spring, Unbalanced, O-ring pusher
• Rotary seat with a snap ring holds all parts together in a unitised design which eases installation and removal
• Torque transmission by set screws
• Conform with DIN24960 standard

Recommended applications

• Chemical industry
• Industry pumps
• Process Pumps
• Oil refining and petrochemical industry
• Other Rotating Equipment

Operating range

•Shaft diameter: d1=18…100 mm
•Pressure: p=0…1.7Mpa(246.5psi)
•Temperature: t = -40 °C ..+200 °C(-40°F to 392°)
•Sliding velocity: Vg≤25m/s(82ft/m)
•Notes: The range of pressure, temperature and sliding velocity is depend on seals combination materials

Combination material

Rotary Face
Silicon carbide (RBSIC)
Tungsten carbide
Carbon graphite resin impregnated
Stationary Seat
99% Aluminium Oxide
Silicon carbide (RBSIC)
Tungsten carbide
Elastomer
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
PTFE Enwrap Viton
Spring
Stainless Steel (SUS304)
Stainless Steel (SUS316
Metal Parts
Stainless Steel (SUS304)
Stainless Steel (SUS316)
W58U data sheet in (mm)

W58U Data Sheet (mm)

SizedD1D2D3L1L2L3
1414242125231218.5
1616262327231218.5
18183227332413.520.5
20203429352413.520.5
22223631372413.520.5
242438333926.713.320.3
2525393440271320
28284237433012.519
303044394530.51219
323246424830.51219
333347424830.51219
353549445030.51219
3838544956321320
4040565158321320
4343595461321320
4545615663321320
4848645966321320
50506662703413.520.5
53536965733413.520.5
55557167753413.520.5
58587870783913.520.5
60608072803913.520.5
63639375833913.520.5
65658577853913.520.5
68688881903913.520.5
70709083924514.521.5
75759588974514.521.5
808010495105451522
8585109100110451522
9090114105115501522
9595119110120501522
100100124115125501522

Description

W58U General Purpose DIN Multi-spring O-ring Pusher Seal is a replacement seal supplied for general pump duty. Most units go into food and beverage process lines. Bore and shaft tolerances follow the original part, so no adaptor is needed.

The design is built around a multi-spring carrier that spreads the spring load evenly over the sealing face. Faces are silicon carbide against carbon graphite, with NBR secondary sealing as standard. It is a balanced design, so face loading stays controlled as pressure rises.

Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. A short dry run is enough to score the faces, so prime the chamber before start-up.

Fitting follows the standard procedure: measure shaft diameter, chamber depth and working height, then set the seal to the recorded dimension before the pump is reassembled. Wear normally appears first at the faces, then at the secondary seals; a leaking unit usually shows both by the time it is pulled.

EPDM covers water and dilute chemical service but not mineral oils; FKM handles oils, fuels and many solvents; FFKM is reserved for aggressive media where the softer elastomers swell. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.

Quote the pump model, shaft diameter and medium when enquiring, and the seal is matched to the original part number. The unit belongs to the mechanical seal line. For a different shaft size, see W59U General Purpose DIN Multi-spring PTFE Wedge Seal or W8T Multi-spring Mechanical Seal Replacement of John Crane 8-1T. Include the quantity and the required elastomer option with the enquiry.

The reference carried by this unit is W58U. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.