


W502 John Crane Type 502 Replacement Unitized Elastomer Bellows Seal For Pumps
Product Features
With full enclosed elastomer bellows design
Insensitive to shaft play and run out
Bellows should not twist due to bi-directional and robust drive
Single seal and single spring
Conform with DIN24960 standard
Design Features
• Completely assembled one-piece design for fast installation
• Unitized design incorporates positive retainer/key drive from bellows
• Non-clogging, single coil spring provides greater dependability than multiple spring designs. Will not be affected by build-up of solids
• Full convolution elastomeric bellows seal designed for confined spaces and limited gland depths. Self-aligning feature compensates for excessive shaft end play and run-out
Recommended applications
• Paints and inks
• Water
• Weak acids
• Chemical processing
• Conveyor and industrial equipment
• Cryogenics
• Food processing
• Gas compression
• Industrial blowers and fans
• Marine
• Mixers and agitators
• Nuclear service
• Offshore
• Oil and refinery
• Paint and ink
• Petrochemical processing
• Pharmaceutical
• Pipeline
• Power generation
• Pulp and paper
• Water systems
• Wastewater
• Treatment
• Water desalination
Operating range
Shaft diameter: d1=14…100 mm
• Temperature: -40°C to +205°C (depending on materials used)
• Pressure: up to 40 bar g
• Speed: up to 13 m/s
Notes: The range of preesure,temperature and speed is depend on seals combination materials
Combination material
Rotary Face
Carbon graphite resin impregnated
Silicon carbide (RBSIC)
Hot-Pressing Carbon
Stationary Seat
Aluminium oxide (Ceramic)
Silicon carbide (RBSIC)
Tungsten carbide
Auxiliary Seal
Nitrile-Butadiene-Rubber (NBR)
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless Steel (SUS304)
Metal Parts
Stainless Steel (SUS304)
W502 Dimension Data Sheet (mm)
Description
W502 John Crane Type 502 Replacement Unitized Elastomer Bellows Seal For Pumps is a like-for-like replacement unit for standard pump seal chambers. Typical duty is food and beverage process lines. Bore and shaft tolerances follow the original part, so no adaptor is needed.
Internally the seal uses an elastomer bellows that seals on the shaft without a separate gasket. Faces are carbon graphite against silicon carbide, with NBR secondary sealing as standard. The unit is unbalanced, which suits the lower pressure range it is designed for.
Temperature, pressure and speed limits depend on the face and elastomer combination, so the duty point should be checked against the datasheet before the order is released. Running the pump dry, even briefly, will damage the faces.
Check the shaft for wear at the secondary seal track and the chamber for scoring before the new unit goes on. Wear normally appears first at the faces, then at the secondary seals; a leaking unit usually shows both by the time it is pulled.
As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Fitting a complete replacement keeps the face load and working height as they left the factory, rather than rebuilding the stack on site. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.
Pricing and availability follow the pump model and shaft size given on the enquiry. The unit belongs to the mechanical seal line. Two close alternatives are W1A Elastomer Bellows Shaft Seal replace John crane type 1A and Type W1 Elastomer Bellows Shaft Pump Seal Replaced John Crane Type 1. Include the quantity and the required elastomer option with the enquiry.
The reference carried by this unit is W502. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.