


W2100 Elastomer Bellow Mechanical Seal Replacement of John Crane 2100
Features
Unitized construction allows for fast and easy installation and replacement. Design fits DIN24960, ISO 3069 and ANSI B73.1 M-1991 standards.
Innovative bellows design is pressure-supported and will not crease or fold under high pressure.
Non-clogging, single-coil spring keeps seal faces closed and properly tracking during all phases of operation.
Positive drive through interlocking tangs will not slip or break free during upset conditions.
Available in the widest array of material options, including high performance silicon carbides.
Recommended applications
Centrifugal pumps
Vacuum pumps
Submerged motors
Compressor
Agitation equipment
Decelerators for sewage treatment
Chemical engineering
Pharmacy
Paper making
Food processing
Mediums: clean water and sewage, mostly used in industries such as sewage treatment and papermaking.
Customization: Changes of materials for getting other operating parameters are possible. Contact us with your requirements.
Operating range
Shaft diameter: d1=10…100mm(0.375” …3.000”)
Pressure: p=0…1.2Mpa(174psi)
Temperature: t = -20 °C …150 °C(-4°F to 302°F)
Sliding velocity: Vg≤13m/s(42.6ft/m)
Notes: The range of pressure, temperature and sliding velocity is depend on seals combination materials
Combination material
Rotary Face
Carbon graphite resin impregnated
Hot-Pressing carbon
Silicon carbide (RBSIC)
Stationary Seat
Aluminium oxide (Ceramic)
Silicon carbide (RBSIC)
Tungsten carbide
Elastomer
Nitrile-Butadiene-Rubber (NBR)
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless steel (SUS304, SUS316)
Metal Parts
Stainless steel (SUS304, SUS316)
W2100 DIMENSION DATA SHEET (INCHES)
DIMENSION DATA SHEET (MM)
L3= Standard seal working length.
L3*= Working length for seals to DIN L1K (seat not included).
L3**= Working length for seals to DIN L1N (seat not included).
Description
W2100 Elastomer Bellow Mechanical Seal Replacement of John Crane 2100 is a replacement mechanical seal built to a standard mounting envelope. It is normally specified for marine and offshore auxiliary pumps. Bore and shaft tolerances follow the original part, so no adaptor is needed.
The working element is an elastomer bellows that seals on the shaft without a separate gasket. The face pair is silicon carbide running on carbon graphite; secondary seals are NBR. The unit is unbalanced, which suits the lower pressure range it is designed for.
Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. Running the pump dry, even briefly, will damage the faces.
Fitting follows the standard procedure: measure shaft diameter, chamber depth and working height, then set the seal to the recorded dimension before the pump is reassembled. A seal that has run dry shows heat colouring on the faces before it shows a leak.
As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Fitting a complete replacement keeps the face load and working height as they left the factory, rather than rebuilding the stack on site. Keeping one unit on the shelf cuts the downtime that follows a leak, since the pump does not have to wait for a part to arrive.
Send the nameplate data with the model and shaft size, and the unit is checked against the original drawing. The unit belongs to the mechanical seal factory line. For a different shaft size, see AES P02 Elastomer Bellow Mechanical Seal John Crane Type 2 N SEAT or W502 John Crane Type 502 Replacement Unitized Elastomer Bellows Seal For Pumps. Include the quantity and the required elastomer option with the enquiry.
The reference carried by this unit is W2100. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.