
W2 Multi-purpose Non-pusher Elastomer Bellows Seal
Features
• Fits equipment with confined space requirements and limited seal chamber depths in pumps, mixers, blenders, agitators, compressors and other rotary shaft equipment.
• To absorb both breakout and running torque, the seal is designed with a drive band and drive notches that eliminate overstressing of bellows. Slippage is eliminated, protecting the shaft and sleeve from wear and scoring.
• Automatic adjustment compensates for abnormal shaft-end play and run-out, primary ring wear and equipment tolerances. Axial and radial shaft movement is compensated for with uniform spring pressure.
• Special balancing allows for higher pressure applications, greater operating speeds and lower wear.
• Non-clogging, single-coil spring allows for greater dependability than multiple spring designs, and it will not run foul due to fluid contact.
Design features
• Mechanical drive – Eliminates overstressing of the elastomer bellows
• Self-aligning capability – Automatic adjustment compensates for abnormal shaft end play runout, primary ring wear and equipment tolerances
• Special balancing – Allows operation at higher pressures
• Non-clogging, single-coil spring – Not affected by buildup of solids
Recommended applications
Process pumps
For pulp and paper
food processing,
water and wastewater
refrigeration
chemical processing
other demanding application
Operating range
• Temperature: -40°C to 205°C/-40°F to 400°F (depending on materials used)
• Pressure: 2: up to 29 bar g/425 psig 2B: up to 83 bar g/1200 psig
• Speed: see enclosed speed limits chart
Combination material
ROTARY FACES: Carbon Graphite, Silicon Carbide, Tungsten Carbide
STATIONARY SEATS: Ceramic, Silicon Carbide, Tungsten Carbide, Stainless Steel
BELLOWS: Viton, EPDM, Neoprene
METAL PARTS: 304 SS standard or 316 SS option available
W2 Data Sheet of Dimension(inches)
Packing & Delivery
We usually deliver the goods by express like DHL, Fedex, TNT, UPS, but we can also ship the goods by air or by sea if the goods weight and volume is big.
For the packing, we pack each seal with plastic film and then in plain white box or brown box. And then in strong carton.
Description
W2 Multi-purpose Non-pusher Elastomer Bellows Seal is a like-for-like replacement unit for standard pump seal chambers. Typical duty is clean water and light chemical service. Bore and shaft tolerances follow the original part, so no adaptor is needed.
The design is built around an elastomer bellows that seals on the shaft without a separate gasket. Standard build pairs carbon graphite with silicon carbide faces and NBR O-rings. The unit is unbalanced, which suits the lower pressure range it is designed for.
Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. Running the pump dry, even briefly, will damage the faces.
Before fitting, record shaft diameter, seal chamber bore and depth; the axial working height is set from those three measurements, not from the old seal alone. Wear normally appears first at the faces, then at the secondary seals; a leaking unit usually shows both by the time it is pulled.
EPDM covers water and dilute chemical service but not mineral oils; FKM handles oils, fuels and many solvents; FFKM is reserved for aggressive media where the softer elastomers swell. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. Keeping one unit on the shelf cuts the downtime that follows a leak, since the pump does not have to wait for a part to arrive.
Orders are matched on pump model, shaft size and medium. The unit belongs to the mechanical seal line. For a different shaft size, see W502 John Crane Type 502 Replacement Unitized Elastomer Bellows Seal For Pumps or W1A Elastomer Bellows Shaft Seal replace John crane type 1A. Include the quantity and the required elastomer option with the enquiry.