Type W21 Single Spring Pump Seals Replaced John Crane Type 21

Features

• The drive band’s “dent and groove” design eliminates overstressing of the elastomer bellows to prevent bellows slip and protect the shaft and sleeve from wear
• Non-clogging, single-coil spring provides greater dependability than multiple spring designs and will not foul due to fluid contact
• Flexible elastomer bellows automatically compensates for abnormal shaft-end play, run-out, primary ring wear and equipment tolerances
• Self-aligning unit automatically adjusts for shaft end play and run-out
• Eliminates potential shaft fretting damage between the seal and shaft
• Positive mechanical drive protects the elastomer bellows from overstressing
• Single coil spring improves tolerance to clogging
• Simple to fit and field repairable
• Can be used with practically any type of mating ring

Analogue for

AESSEL P04, AESSEL P04T, Burgmann MG921 / D1-G55, Flowserve 110, Hermetica M112K.5SP, John Crane 21, LIDERING LRB01, Roten 21A, Sealol 43CU short, US Seal C, Vulcan 11

Recommended applications

Centrifugal Pumps
Slurry Pumps
Submersible Pumps
Mixers & Agitators
Compressors
Autoclaves
Pulpers

Operating range

• Temperature: -40˚F to 400°F/-40˚C to 205°C (depending on materials used)
• Pressure: up to 150 psi(g)/11 bar(g)
• Speed: up to 2500 fpm/13 m/ s (depending on configuration and shaft size)
• This versatile seal can be used on a wide range of equipment including centrifugal, rotary and turbine pumps, compressors, mixers, blenders, chillers, agitators, and other rotary shaft equipment
• Ideal for pulp and paper, pool and spa, water, food processing, wastewater treatment, and other general applications

Combination material

Rotary Face
Carbon graphite resin impregnated
Silicon carbide (RBSIC)
Hot-Pressing Carbon C
Stationary Seat
Aluminium oxide (Ceramic)
Silicon carbide (RBSIC)
Tungsten carbide
Auxiliary Seal
Nitrile-Butadiene-Rubber (NBR)
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless Steel (SUS304, SUS316)
Metal Parts
Stainless Steel (SUS304, SUS316)

w21

Type W21 DIMENSION DATA SHEET (INCHES)

W21 DIMENSION DATA SHEET

Description

Type W21 Single Spring Pump Seals Replaced John Crane Type 21 is a replacement mechanical seal built to a standard mounting envelope. It is normally specified for clean water and light chemical service. Bore and shaft tolerances follow the original part, so no adaptor is needed.

The design is built around an elastomer bellows that seals on the shaft without a separate gasket. Faces are carbon graphite against silicon carbide, with NBR secondary sealing as standard.

Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. Running the pump dry, even briefly, will damage the faces.

Before fitting, record shaft diameter, seal chamber bore and depth; the axial working height is set from those three measurements, not from the old seal alone. A seal that has run dry shows heat colouring on the faces before it shows a leak.

As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.

Orders are matched on pump model, shaft size and medium. The unit belongs to the mechanical seal line. Related units in the same family include Type W1 Elastomer Bellows Shaft Pump Seal Replaced John Crane Type 1 and Elastomer rubber mechanical seals Vulcan Type 19B for water pump. Include the quantity and the required elastomer option with the enquiry.

The reference carried by this unit is W21. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.