Type W1 Elastomer Bellows Shaft Pump Seal Replaced John Crane Type 1

Replacement of Below Mechanical Seals

Burgmann MG901, John crane Type 1, AES P05U, Flowserve 51, Vulcan A5

Technical Features

Unbalanced
Single Spring
Bi-directional
Elastomer Bellows
Set screw lock collars available

Designed Features

To absorb both breakout and running torque, the seal is designed with a drive band and drive notches that eliminate overstressing of bellows. Slippage is eliminated, protecting the shaft and sleeve from wear and scoring.

Automatic adjustment compensates for abnormal shaft-end play, run-out, primary ring wear and equipment tolerances. Uniform spring pressure compensates for axial and radial shaft movement.

Special balancing accommodates higher-pressure applications, greater operating speeds and lower wear.

Non-clogging, single-coil spring allows for greater dependability than multiple spring designs. Will not run foul due to fluid contact.

Low drive torque improves performance and reliability.

Recommended applications

Water and waste water technology
Petroleum chemical industry
Industrial pumps
Process pumps
Other Rotating Equipment

Operating range

Temperature: -40°C to 205°C/-40°F to 400°F (depending on materials used)

Pressure: 1: up to 29 bar g/425 psig 1B: up to 82 bar g/1200 psig
Speed: 20 M/S 4000 FPM
Standard size:12-100mm or 0.5-4.0 inch

Notes: The range of preesure,temperature and sliding velocity is depend on seals combination materials

Combination material

Rotary Face
Carbon graphite resin impregnated
Tungsten carbide
Silicon carbide (RBSIC)
Stationary Seat
Aluminium oxide(Ceramic)
Silicon carbide (RBSIC)
Tungsten carbide 1
Auxiliary Seal
Nitrile-Butadiene-Rubber (NBR)
Fluorocarbon-Rubber (Viton)
Ethylene-Propylene-Diene (EPDM)
Spring
Stainless Steel (SUS304, SUS316)
Metal Parts
Stainless Steel (SUS304, SUS316)

w1

TYPE W1 Dimension Data Dheet (inches)

W1 dimension data sheet

Description

Type W1 Elastomer Bellows Shaft Pump Seal Replaced John Crane Type 1 is a like-for-like replacement unit for standard pump seal chambers. It is normally specified for process water in general industry. Bore and shaft tolerances follow the original part, so no adaptor is needed.

The design is built around an elastomer bellows that seals on the shaft without a separate gasket. The face pair is carbon graphite running on silicon carbide; secondary seals are NBR. The unit is unbalanced, which suits the lower pressure range it is designed for.

Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. A short dry run is enough to score the faces, so prime the chamber before start-up.

Before fitting, record shaft diameter, seal chamber bore and depth; the axial working height is set from those three measurements, not from the old seal alone. A seal that has run dry shows heat colouring on the faces before it shows a leak.

As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Fitting a complete replacement keeps the face load and working height as they left the factory, rather than rebuilding the stack on site. Keeping one unit on the shelf cuts the downtime that follows a leak, since the pump does not have to wait for a part to arrive.

Replacement orders are confirmed against the original part number and the shaft size. The unit belongs to the mechanical seal supplier line. Related units in the same family include W1A Elastomer Bellows Shaft Seal replace John crane type 1A and W502 John Crane Type 502 Replacement Unitized Elastomer Bellows Seal For Pumps. Include the quantity and the required elastomer option with the enquiry.