An IMO rotor set is the matched hydraulic group inside a three-screw pump: one power rotor and two idler rotors, lapped to each other and to the housing bore they run in. Once that group wears, the pump loses flow and pressure slowly, and the loss is easy to blame on the seal, the relief valve or the driver. Rotor sets here are identified by pump family and size, then by a G012 code and a letter-number suffix such as K7, N7, L3 or N6.

Victor supplies rotor sets for IMO ACE, ACG, ACD and ACP pumps, with part numbers running from 178913 and 179507 through 187542, 187559, 187567, 190483 and the P062885 and P062893 ACD/ACP units. Every set is built to the size and variant code, not to a nominal flow figure.

Rotor set types used on IMO pumps

ACE pumps use the shorter rotor group, listed here for ACE 25 in L3, ACE 32 in L3 and N3, and ACE 38 N3 under part 190483. ACG pumps take the longer group: ACG 45, 52 and 60 in K7 and N7, covering 178913 through 187567.

ACD and ACP 025 pumps use the 025 L6 and N6 variants, P062885 and P062893. The suffix is not decoration: L and N identify different rotor geometry, and a set built for N6 will not restore performance in an L6 housing even when the nominal size matches.

How to identify the right replacement

The nameplate gives family and size, and the IMO parts list gives the rotor set number. Where the plate is unreadable, housing bore, rotor outside diameter and end clearance identify the set, provided they are measured with the pump stripped and cleaned. Why the rotor set governs IMO performance explains what changes when only part of the group is replaced.

  • Pump model: ACE, ACG, ACD or ACP plus the size number, for example ACG 52 or ACE 32.
  • Part number: 178913, 179507, 179515, 187542, 187559, 187567, 190483, 190484, 190485, 190486, 190487, P062885 or P062893.
  • Rotor outside diameter: measure the power rotor and both idlers at the same axial position, away from the wear track.
  • End clearance: check the rotor-to-cover gap before ordering; a worn thrust face changes which set fits.

Materials and duty limits

The rotors are hardened steel running in a cast housing, and performance depends on the lapped clearance between them. Fuel oil and lube oil service keeps that clearance stable while the oil stays clean; abrasive contamination opens it and the flow curve drops.

Temperature is set by the pumped fluid and the seal, not by the rotor set, and pressure capability comes from rotor length and the number of starts. A set correct for a short ACE build will not deliver the same pressure in a longer ACG housing.

What we supply for IMO pumps

Cross-reference notes

The cross-reference on this page is the IMO part number itself. ACG 45, 52 and 60 each appear under both K7 and N7 suffixes, and those are separate parts rather than interchangeable stock: 178913 and 187542 cover ACG 45 in N7 and K7, 179507 and 187559 cover ACG 52, and 179515 and 187567 cover ACG 60. ACE runs 190483 for the 38 N3, 190484 and 190485 for the 32 N3 and L3, 190486 and 190487 for the 25 L3. ACD and ACP split between P062885 for 025 L6 and P062893 for 025 N6.

FAQ

Can one rotor be replaced on its own?

No. The power rotor and the two idlers are lapped as a group, and their clearance is what makes the pump work. A single new rotor against two worn ones will not hold pressure at rating.

What usually kills an IMO rotor set?

Abrasive contamination and running with a starved suction. Both open the rotor clearance, and the first symptom is a flow drop at unchanged discharge pressure.

IMO Pump Rotor Set

IMO PUMP ROTOR SET G012 ACE 32 N3 P190484

IMO PUMP ROTOR SET G012 ACE 32 L3 P190485

Rotor set for IMO pump ACD/ACP 025 L6 G012 P062885

Rotor set for IMO pump ACD/ACP 025 N6 G012 P062893

IMO PUMP ROTOR SET G012 ACE 25 L3 P190487

IMO PUMP ROTOR SET G012 ACE 25 L3 P190486

IMO pump rotor set G012 for ACE 38 N3 190483

IMO pump rotor set G012 ACG 45 N7 178913

IMO pump rotor G012 ACG 45 K7 187542

IMO pump rotor set G012 ACG 60 K7 187567

IMO pump ACG 52 rotor set G012 N7 179507

IMO pump rotor set G012 ACG 52 K7 187559

IMO pump ACG G012 60 N7 rotor set 179515