
Alfa Laval-6 pump Seal replace John Crane 87 (EI/ EC) and AES W03
Operational Conditions
Temperature:-40℃ to +200℃
Pressure: ≤0.8MPa
Speed: ≤18m/s
Applications
Clean water,
sewage water
oil and other moderately corrosive fluids
Materials
Stationary Ring: Silicon Carbide, TC, Carbon
Rotary Ring: Silicon Carbide, SUS304, SUS316, TC
Secondary Seal: NBR, EPDM, Viton
Spring and Metal Parts: SUS304, SUS316
Alfa Laval-6 data sheet of dimension
About Alfa laval LKH pump
Applications
The LKH pump is a highly efficient and economical centrifugal pump, which meets the requirements of hygienic and gentle product treatment and chemical resistance. LKH is available in thirteen sizes, LKH-5.-10.-15, -20, -25.-35, -40, -45, -50.-60.-70, 85 and -90.
Standard design
The LKH pump is designed for CIP with emphasis on large internal radii and cleanable seals. The hygienic version of LKH has a stainless steel shroud for protection of the motor, and the complete unit is supported on four adjustable stainless steel legs.
Shaft seals
The LKH pump is equipped with either an external single or a flushed shaft seal. Both have stationary seal rings made from stainless steel AISI 329 with sealing surface in silicon carbide and rotating seal rings in carbon. The secondary seal of the flushed seal is a long lasting lip seal the pump may also be equipped with a double mechanical shaft seal.
Our advantages
R&D Department
we have more than 10 professional engineers, keep strong ability for mechanical seal design, manufacturing and offer seal solution
Mechanical Seal Assemble Line
Lepu seal spend lots of money to train our workers, and make sure our workers have good skill for mechanical seal.
Mechanical seal warehouse.
we keep many seals in our stock, and deliver them fast to our customers, like grundfos pump seal, flygt pump seal, burgmann seal, john crane seal, and so on.
Description
Alfa Laval-6 pump Seal replace John Crane 87 (EI/ EC) and AES W03 covers Alfa Laval pump duty as a direct replacement for the original part. Typical duty is building services and HVAC plant. Bore and shaft tolerances follow the original part, so no adaptor is needed.
The working element is a spring-loaded pusher assembly. The face pair is tungsten carbide running on silicon carbide; secondary seals are FKM. The unit is unbalanced, which suits the lower pressure range it is designed for.
Exact limits follow the face material and elastomer choice; confirm the duty point against the datasheet for the specific build. A short dry run is enough to score the faces, so prime the chamber before start-up.
Measure shaft diameter, chamber depth and working height before stripping the old unit; the new seal is set to those numbers, not to the dimensions of the worn part. A seal that has run dry shows heat colouring on the faces before it shows a leak.
As a rule, EPDM suits water-based duty, FKM suits oils and fuels, and FFKM is used where solvents would swell the other two. Replacing the complete unit rather than single components avoids re-setting the working height, which is where most repeat failures start. A spare on site is worth holding for critical pumps, where a leaking seal takes the whole line out of service.
Orders are matched on pump model, shaft size and medium. The unit belongs to the Victor’s OEM seal replacement line. For a different shaft size, see Alfa Laval-3 Mechanical Seal replace Vulcan Type 91 22MM AES P07 or Alfa Laval-5 Laval pump seals replace Vulcan Type 93. Include the quantity and the required elastomer option with the enquiry.
The reference carried by this unit is W03. Confirm that reference against the pump nameplate and the shaft size before the order is placed, since later versions of the same pump can use a different seal arrangement.